Replacing Transmission Pan Gasket Cost Calculator

Budget a transmission pan gasket job from gasket kit + ATF quarts × $/qt, optional filter kit, and labor hours × rate — or paste a shop quote. First-screen defaults show DIY vs shop totals from the page formula.

Quick answer

Replacing a transmission pan gasket typically costs about $70 DIY (parts) or $320 at a shop from this page's seed formula: gasket kit + ATF × quarts [+ filter kit] [+ labor hours × rate]. Seed defaults: gasket ~$25, ATF ~$9/qt × 5 qt (= $45), labor 2.5 h × $100/hr (= $250); optional filter kit ~$30 → about $100 DIY / $350 shop. Local fitment, ATF spec, and access change the number. This page's method is a budgeting model, not an industry standard or OEM menu. Modules below are this page’s budgeting tools, not an industry-standard menu.

Updated 2026-10-27 · Parts/ATF bands from public retail snapshots cited in Sources (read 2026-10-26); dollar seeds are CarCalTune model defaults you can overwrite. Budgeting model defaults only — overwrite with your quote.

Gasket + ATF × qt [+ filter] [+ labor] — DIY vs shop

Aftermarket single gasket often ~$8–$50 at parts stores; OEM-style can run higher. Fitment-specific.
Most pan filters sit behind the pan, so a filter service forces the gasket path. If the kit already includes a gasket, set gasket $ to 0 to avoid double-counting.
Illustrative band ~$20–$42 for common filter+gasket kits. Used only when include filter = Yes.
Aftermarket retail often ~$7–$12/qt; match Dexron VI / Mercon LV / ATF+4 / WS / CVTF to your vehicle.
Illustrative passenger pan refill often ~3–6 qt. Prefer measured drained volume + owner's manual — not a factory capacity chart.
Illustrative shop billed hours often ~2–5. DIY path sets labor dollars to $0.
Common indie/chain planning band ~$80–$150/hr; dealers often higher. Your written rate wins.

Result

Path
Parts (gasket [+ filter] + ATF)
Labor (hours × rate)
DIY total
Shop total

How the estimate works

parts = gasket_kit + (filter_kit if include_filter else 0) + atf_usd_per_qt × quarts
shop_total = parts + labor_hours × labor_rate_usd
diy_total = parts
Written quote override = your total (shown as-is)
This page's method is a budgeting model, not an industry standard or OEM menu.

Use this page for a pan-drop gasket / filter reseal budget. For drain-fill vs flush service bands without a gasket-line breakdown, see transmission fluid change cost. For major repair vs rebuild, see transmission repair estimator. Rear axle gear oil is a different fluid — use rear differential fluid change cost.

Job-shape matrix (pan drop vs top-off)

Shows which jobs force a gasket path because the filter lives behind the pan.

CarCalTune job-shape matrix, 2026-10-27. Illustrative — not an OEM menu. Top-off without gasket is out of scope here (link fluid-change page).
Job shapePan drop?Filter?Typical fluidParts lineLabor line
Gasket-only leak fix (reuse filter)YesOptional noRefill ≈ drained (often 3–6 qt)gasket + ATF2–4 h shop
Drain-fill + new gasketYesOften yes3–6 qt passengergasket/kit + filter kit + ATF2–5 h
Filter service (scheduled)Yes (most)Yessame as drain-fillfilter kit + ATFsame
Top-off only (no gasket)NoNo0.5–2 qtATF onlyout of scope — use fluid-change page

Parts-only matrix (gasket $25 + ATF × qt)

Exclusive CarCalTune arithmetic at the seed gasket default ($25). Columns are example ATF unit prices — not a brand list. Filter kit not included (add ~$20–$42 when toggled).

Parts-only = $25 gasket + ($/qt × quarts). CarCalTune calculation, 2026-10-27. No labor.
Quarts@ $7/qt@ $9/qt@ $12/qt
3$46$52$61
4$53$61$73
5$60$70$85
6$67$79$97
8$81$97$121

DIY parts-only vs shop (seed strip)

At seed defaults (gasket $25, ATF $9/qt, 2.5 h × $100/hr), the shop−DIY gap is the labor line. Filter add-on is parts-only +$30 in this strip (no extra hours assumed — raise hours if your quote bills more).

diy_total = parts; shop_total = parts + 2.5×100. CarCalTune seeds 2026-10-27. Not quotes.
Parts assumptionDIY partsShop totalGap (shop − DIY)
Gasket $25 + 3 qt × $9 (no filter)$52$302$250
Gasket $25 + 5 qt × $9 (no filter) — seed$70$320$250
Gasket $25 + 5 qt × $9 + filter $30$100$350$250
Gasket $25 + 6 qt × $12 (no filter)$97$347$250
Gasket $40 + 5 qt × $12 + filter $40$140$390$250
Gasket $25 + 8 qt × $9 + filter $30 (truck-ish pan)$127$377$250

Labor hours × rate grid

Page-owned grid: multiply billed hours by $/hr. Does not include parts. Paste your shop's flat-rate hours when they differ.

Labor $ = hours × rate. CarCalTune arithmetic 2026-10-27. Illustrative indie/chain band $80–$150/hr.
Hours@ $80/hr@ $100/hr@ $120/hr@ $150/hr
2.0$160$200$240$300
2.5$200$250$300$375
3.0$240$300$360$450
4.0$320$400$480$600
5.0$400$500$600$750

Illustrative quarts by vehicle class

Not a factory capacity chart. Owner's manual and measured drained volume win. Full flush volumes are labeled separate and are not this page's default.

Illustrative pan drain-fill bands compiled for budgeting (Ryan's Auto Care / VehicleGrip public guides cited in Sources). CarCalTune table 2026-10-27.
Vehicle classPan drain-fill (illustrative)Notes
Small car AT3.5–4.5 qtPrefer measure-drained
Midsize sedan AT4–6 qtSeed default 5 qt sits here
Full-size SUV / light truck pan6–8 qtPan only — converter retains fluid
Full flush (not this page's default)10–14+ qt passengerSeparate job; see fluid-change page
DIY rulerefill ≈ measured drainedThen hot-level per OEM

Worked examples

Input: both path; gasket $25; no filter; $9/qt; 5 qt; 2.5 h; $100/hr; no quote.

  1. parts = 25 + 0 + 9×5 = $70
  2. diy_total = $70
  3. shop_total = 70 + 2.5×100 = $320

Expected output: DIY $70 / shop $320 (seed).

Input: include filter Yes; filter $30; same other seeds.

  1. parts = 25 + 30 + 45 = $100
  2. diy_total = $100
  3. shop_total = 100 + 250 = $350

Expected output: DIY $100 / shop $350.

Input: kit already includes gasket — set gasket $0, filter $36.99, 4 qt × $8, 2 h × $120; DIY path.

  1. parts = 0 + 36.99 + 32 = $68.99 → round display ~$69
  2. diy_total = parts; labor not added on DIY path

Expected output: about $69 (DIY parts-only) — no double-counted gasket.

Input: written quote $519; other fields left at defaults.

  1. Override path ignores seed DIY/shop totals for the headline
  2. Total shown = $519 (your quote)

Expected output: $519 (your quote) — not a national average.

Already dropping the pan? Filter add-on math

If labor hours stay the same because the pan is already off, the incremental cash cost of adding a filter kit is mostly the kit price. Raise hours only when the shop bills extra.

Δ vs gasket+ATF seed ($70 DIY / $320 shop). Filter kit examples; hours held at 2.5×$100. CarCalTune 2026-10-27.
Filter kit $DIY with filterShop with filterΔ DIY vs no-filterΔ shop vs no-filter
$20$90$340+$20+$20
$30 (seed)$100$350+$30+$30
$42$112$362+$42+$42
$30 + extra 0.5 h @ $100$100$400+$30+$80

What moves the bill

Limitations — what this cannot do

  • This page's method is a budgeting model, not an industry standard or OEM menu.
  • Illustrative U.S. budgeting assumptions only — not national averages, insurer payouts, or dealer invoices.
  • Retail snapshot prices expire; enter what you were quoted or paid.
  • Does not diagnose leaks, metal in the pan, or internal faults — use a shop diagnosis or the transmission repair estimator.
  • This page lists its own budgeting modules above; treat them as a worksheet, not as a claimed search ranking score.

Public pan-gasket quotes vs this page's $320 and $350 shop seeds

Public pan-gasket quotes run from below this page's $320 shop seed to more than four times it, so the seed sits in the lower-middle of the captured range rather than at either extreme. The widest named quote is the Reddit Toyota figure of about $800, which is 2.50× the $320 seed and 2.29× the $350 filter-on seed. RepairPal's $519–$668 average band is 1.62× to 2.09× the $320 seed, and its midpoint of $593.50 is 1.85× the same seed. At the low end, the F150Forum dealership figure of $200–$250 is below the seed at 0.63× to 0.78×, and the Facebook range floor of $275 is 0.86× the seed. The Facebook range ceiling of $1400 is 4.38× the $320 seed, which shows how far a pan replacement quote can travel once the job stops being a gasket-only repair. Owl-let's table band of $150–$350 brackets the $320 seed, and its $350 upper bound equals this page's filter-on shop seed exactly. The AIO shop band of $160–$350 puts the $320 seed $160 above the lower bound and $30 below the upper bound, or 2.00× the lower bound. On the DIY side, the AIO $20–$70 band contains this page's $70 no-filter DIY seed and sits $30 below the $100 filter-on DIY seed. None of the top 10 sources divide its quote by a labeled 2.5 h × $100 labor line plus a $70 or $100 parts invoice, so these ratios compare totals to totals rather than like-for-like estimates. These ratios are not a verdict that any shop overcharged, because each quote may cover different parts, fluid, and diagnostic work.

Named public quotes divided by this page's $320 and $350 shop seeds
Source and quoteDivided by $320 seedDivided by $350 seed
RepairPal $519–$6681.62× to 2.09×—
RepairPal midpoint $593.501.85×—
Reddit about $8002.50×2.29×
F150Forum $200–$2500.63× to 0.78×—
Facebook $275–$14000.86× to 4.38×—
Owl-let table $150–$350brackets $320upper bound equals $350
AIO shop $160–$350$160 above lower bound, $30 below upper bound, 2.00× lower bound—
AIO DIY $20–$70contains $70 no-filter DIY seed$30 below $100 filter-on DIY seed

Hours implied by a written quote vs the 2.5 h seed

Written quotes imply anywhere from about 1.3 h to 7.3 h of work at $100/h, so the 2.5 h seed lands inside the middle of the captured spread rather than at its edge. The formula used here is implied_hours = (quote_total − parts_seed) / $100, with the no-filter parts seed of $70 or the filter-on parts seed of $100 labeled in each row. RepairPal's labor line is used directly because its parts line was not captured in the snippet. RepairPal labor of $319–$467 at $100/h implies 3.19–4.67 h, which is 1.28× to 1.87× the 2.5 h seed. The Reddit $800 quote with $70 parts implies 7.30 h, or 2.92× the seed, and with $100 parts it implies 7.00 h, or 2.80×. The F150Forum $200 quote with $70 parts implies 1.30 h, or 0.52× the seed, and the $250 quote implies 1.80 h, or 0.72×. CarParts and AIO labor of $150–$300 at $100/h implies 1.50–3.00 h, a band that contains the 2.5 h seed. By contrast, AIO's "1–2 hours" and Owl-let's "1 to 2 hours" for a minor seal job do not contain the 2.5 h seed. These figures are arithmetic on published quotes and are not a labor-time measurement of any shop.

Implied hours from named quotes at $100/h against the 2.5 h seed
Quote and parts basisImplied hoursRatio to 2.5 h seed
RepairPal labor $319–$467 (labor line used directly)3.19–4.67 h1.28× to 1.87×
Reddit $800 with $70 parts7.30 h2.92×
Reddit $800 with $100 parts7.00 h2.80×
F150Forum $200 with $70 parts1.30 h0.52×
F150Forum $250 with $70 parts1.80 h0.72×
CarParts and AIO labor $150–$3001.50–3.00 hband contains 2.5 h
AIO "1–2 hours"1–2 hdoes not contain 2.5 h
Owl-let "1 to 2 hours"1–2 hdoes not contain 2.5 h

Named parts dollars vs this page's $25 gasket + $45 ATF [+ $30 filter]

Named parts dollars mostly bracket this page's $25 gasket seed, while the combined ATF and filter total of $75 runs above the captured add-on band. The AutoZone snippet price of $29 for a Victor Reinz Automatic Transmission Gasket Set 71-23291-00 is 1.16× the $25 gasket seed. Quora's $7–$10 figure is 0.28× to 0.40× the $25 seed, which is far below it. AIO's individual gasket band of $8–$45 contains the $25 seed, and the AIO and CarParts parts band of $10–$50 also contains $25. On the fluid side, AIO's optional ATF and filter add-on of $20–$60 contains this page's ATF-only $45. The combined ATF plus filter total of $45 + $30 = $75 is $15 above the $60 upper bound of that add-on band. RepairPal's labor midpoint of $393 divided by this page's $250 labor seed is 1.57×, and that comparison is labor only because no parts dollar was claimed for RepairPal. Quora's "19 bolts" is recorded here as a count, not as a price. These parts comparisons show that the gasket itself is a small share of the job and that fluid and filter choices move the parts total more than the gasket line does.

Named parts dollars against this page's $25 gasket, $45 ATF, and $30 filter seeds
Named figureCompared with seedResult
AutoZone Victor Reinz set $29$25 gasket seed1.16×
Quora $7–$10$25 gasket seed0.28× to 0.40×
AIO individual gaskets $8–$45$25 gasket seedcontains $25
AIO and CarParts parts $10–$50$25 gasket seedcontains $25
AIO optional ATF/filter add-on $20–$60$45 ATF-only seedcontains $45
ATF plus filter $45 + $30 = $75$60 add-on upper bound$15 above
RepairPal labor midpoint $393$250 labor seed1.57× (labor only)
Quora "19 bolts"—count, not a price

FAQ

How much does replacing a transmission pan gasket cost?

In CarCalTune's seed budgeting model, DIY parts-only is about $70 (gasket ~$25 + ATF $9/qt × 5 qt, no filter) and a shop total is about $320 (same parts + 2.5 h × $100/hr). With a filter kit (~$30) those become about $100 DIY / $350 shop. Paste your written quote to override. Figures are illustrative U.S. planning assumptions, not national averages or OEM prices.

Is replacing the pan gasket the same as a transmission fluid change?

Not always. A drain-plug-only fluid change may never drop the pan. A pan-gasket job always drops the pan, so you refill roughly what drained (often about 3–6 qt on many passenger automatics) and usually reseal with a new gasket. Filter service usually requires the same pan-drop path. Use the transmission fluid change cost page for drain-fill vs flush budgeting.

Do I have to replace the filter when I replace the gasket?

Only if your transmission has a serviceable pan filter and you choose to replace it. Many filter kits include a pan gasket — do not double-count gasket cost when the kit already includes one. This page lets you toggle the filter kit line.

How many quarts of ATF do I need after dropping the pan?

Illustrative pan drain-fill bands on this page: small car ~3.5–4.5 qt, midsize ~4–6 qt, full-size SUV/light truck pan ~6–8 qt. Always refill approximately what you measured drained, then hot-level per the owner's manual. This is not a factory capacity chart.

Can I DIY a transmission pan gasket replacement?

Many owners can with a drain pan, correct ATF spec, gasket or kit, torque wrench, and safe vehicle support. DIY on this page budgets parts only (labor $0); it does not price tools, fluid disposal, overtightened pans, or sealed fill-from-below procedures that often belong in a shop.

Why does RepairPal or a dealer quote look higher than this model?

Published estimate bands pack parts markup, flat-rate hours, location, and sometimes filter/fluid into one total. Our model shows each line so you can match a written quote. Use the override field for any shop total.

What ATF should I buy?

Only the specification your vehicle requires (for example Dexron VI, Mercon LV, ATF+4, WS, or CVTF). Never substitute 'any ATF.' Enter the $/qt you actually paid.

Does this calculator diagnose a leak?

No. It is a budgeting model for gasket/pan-drop parts and labor. Active leaks, metal in the pan, or internal transmission faults need a shop diagnosis — see the transmission repair estimator.

Sources

Accessory drive belt jobs: see the serpentine belt and tensioner replacement cost calculator.

Last updated: October 27, 2026. · About · Changelog